![]() Non-deteriorating bond retains strength and flexibility. No bond failure after 25 consecutive days. Hose Stream Test.ġ″ concrete slabs bonded to 1/2″ gypsum plaster subjected to seepage of strong detergents and synthetic urine for 10 hrs. Non-toxic, no ill effects after 7 days.ĪSTM E-119 (bonded assembly). Choosing the right patching repair products depends on the type of damage you’re dealing with. and gypsum mixes to interior concrete, masonry, or plaster surfaces. Whether you’re fixing a small dent or a large hole, we can help make your walls and furniture look new with patching repair products like wood putty, drywall, ready-mixed concrete patch and more. Silpro Weld-O-Bond Bonding Coat is specifically formulated for bonding Portland. Freeze-thaw stable.Įnclosed mice exposed to 30 cc volatized bonding agent for 1 hr. Patch and Repair Your Walls and Furniture With Ease. Avg.ĥ cycles freeze (-10 degrees F and thaw). 14 days.ĪSTM C-109 (specimens brought to 35 degrees F for 1 hr., then to 310 degrees F for 2 hrs). Avg.ĪSTM C-1059 (slant shear cylinder test). 1 Gallon Red Plaster Weld Bonds Plaster To Any Clean Or Structurally Sound Interior Surface Can Be Used Over Oil, Rubber, Vinyl, Silicone Or Latex Paints. 28 days.ĪSTM C-78 (concrete beams laminated with bonding agent). In all cases failure occurred in the cementitious material, not in the bond. Test reports are available upon request.ĪSTM C 932-05 (pulling apart bonded cement briquet halves). casien and calcimine paints), and silicone.ĭata obtained from tests conducted periodically by leading independent laboratories. Weld-Crete® is also used for: bonding setting beds for ceramic tile bonding Portland cement plaster and stucco mixes and to bond to surfaces such as brick, block, tile, marble, metal, glass block, soundly adhered paint (non-soluable in water, i.e. Use Weld-Crete’s® open time to your advantage in bonding to concrete shear walls when you need a time lapse between application of bonding agent, placement of reinforcement steel, placement of formwork and placement of concrete. Weld-Crete®can be "painted on" in a single application 1 hour to 10 days prior to concrete placement. For exterior and interior use, Weld-Crete® will bond new concrete, Portland cement plaster and cementitious mixes to structurally sound concrete floors, walls, columns, beams, steps and ramps. The original chemical concrete bonding agent, Weld-Crete® incorporates polyvinyl acetate homopolymer in a patented formulation. ![]() Plaster-Weld® can be used over paints having oil, rubber or vinyl bases, and over silicone-treated surfaces, as well as latex paints.Weld-Crete® bonds new concrete, stucco, tile setting beds and terrazzo to any structurally sound surface, interior or exterior. sheet lead in x-ray rooms) and marble are suitable sound surfaces, structurally. Concrete, brick, block, glass, ceramic tile, wallboard, metals (e.g. ![]() Plaster-Weld® prepares the surface to allow you to plaster directly to concrete over electric radiant heat cable, and to bond cement mortar beds to smooth concrete for installation of rigid foam insulation. DESIGNED FOR INTERIOR USE ONLY, the high performance bonding of one-coat finish plaster and/or two and three coat work to concrete ceilings, walls, columns, beams, and other structurally sound surfaces. The original chemical plaster bonding agent is a patented formulation incorporating polyvinyl acetate homopolymer. Places Near Atlanta, GA with Plastic Welding. Plaster-Weld® bonds new plaster to any clean, structurally sound, interior surface. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |